A
-
Abdalla, H M
Experimental investigation of star grains in dual thrust solid propellant motors [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-18]
-
Abdalla, H M
Mitigation of irregular burning in a small solid propellant rocket motor [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-17]
-
Abdalla, H M
Validation of a simplified model for liquid propellant rocket engine combustion chamber design [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-14]
-
Abdalla, H M
Validation of r elations for the determination of pyrotechnic igniter mass [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
AbdAllah, A
Improving water desalination efficiency by using carbon nanotubes as pre-treatment [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Abdelaziz, A M
Ultrasonic-assisted drilling of nickel-based super alloy in conel 601: An experimental study [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Abd Elaziz, M
A new artificial neural network model integrated with a cat swarm optimization algorithm for predicting the emitted noise during axial piston pump operation [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Abdeldayem, M A
Design and manufacturing of a test rig for measuring the torque required in soil drilling operations [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Abdelfattah, W
Computational fluid dynamic model for machining using minimum quantity coolant [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Abdelghany, A A
Passive vibration attenuation: a comparison study [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Abdelhamed, M
Effect of modified bouc-wen model parameters on the dynamic hysteresis of magnetorheological dampers [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Abdel-Kader, M A
Penetration of long rods into semi-infinite metallic targets over wide range of impact velocities [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Abdellatif, M H
The effect of tire rubber particles on the mechanical and physical properties of polyester [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Abdellatif, M H
A new integrated product and process development model [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Abd El Maksoud, R M
The effect of rectangular gurney flap on wells turbine performance [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-15]
-
Abdelnaby, M A
Numerical investigations of bistable piezoelectric cantilever for enhanced energy harvesting [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Abdelsalam, O
Transient heat transfer for GPMG's barrel 7.62x51mm [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-8]
-
Abdelsamie, A
Aerodynamic performance improvement using a micro-cylinder as a passive flow control around the S809 airfoil [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Abdelwahhab, S A
Design of bio-inspired muscle sarcomere structure using a hybrid hydrogel-IPMC actuator [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Abo Elenien, K F
The effect of tire rubber particles on the mechanical and physical properties of polyester [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Abo-Elnor, M E
Design and manufacturing of a test rig for measuring the torque required in soil drilling operations [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Aborehab, A
Experimental modal testing of a honeycomb sandwich plate [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Abu-El-Yazied, T G
Fracture toughness assessment of axial partially through cracks in X65 and X70 steel pipes [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Abu-Okail, M
Optimization of friction stir welding parameters using response surface methodology [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Adel, W M
An experimental study on mechanical and ballistic characteristics of different HTPB composite propellant formulations [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Ahmed, H
Interactions between microorganisms and composite material with marble & granite filler [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Ahmed, H
Optical non linear characteristics of particles from natural resources [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Ahmed, H M
Phase stability of mechanically alloyed Ti-Fe-Al alloys [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Ahmed, M
Handling performance of an 8x8 combat vehicle [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Ahmed, M Y
Experimental and computational dynamic structural analysis of free-flight rockets [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Ahmed, M Y M
Multi-fidelity drag prediction for base bleed projectile [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Ali, S
Numerical investigations of bistable piezoelectric cantilever for enhanced energy harvesting [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Al-Makky, M
Ultrasonic-assisted drilling of nickel-based super alloy in conel 601: An experimental study [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Al-Sanabawy, M A
Mitigation of irregular burning in a small solid propellant rocket motor [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-17]
-
Al-Sanabawy, M A
Validation of a simplified model for liquid propellant rocket engine combustion chamber design [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-14]
-
Aly, M H
Development of rotary heat exchanger model to investigate performance with integrating controller [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-16]
-
Amin, M I
Modelling and experimental investigation of high – pressure common rail diesel injection system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Amin, M I
Performance of homogeneous charge compression ignition (HCCI) engine with common rail fuel injection [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Ata, W G
Effect of modified bouc-wen model parameters on the dynamic hysteresis of magnetorheological dampers [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Attai, Y A
An experimental study on mechanical and ballistic characteristics of different HTPB composite propellant formulations [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Attia, T A
Assessment of steel wire's fatigue life using finite elements modelling and experimental testing [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Awad, M I
Assistive exoskeleton hand glove using soft pneumatic actuators: design optimization [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Awad, M I
Design of bio-inspired muscle sarcomere structure using a hybrid hydrogel-IPMC actuator [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Ayman, A
A new integrated product and process development model [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Azab, N A
The effect of tire rubber particles on the mechanical and physical properties of polyester [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Aziz, M M
Multi-fidelity drag prediction for base bleed projectile [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Azzam, B
Improving water desalination efficiency by using carbon nanotubes as pre-treatment [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
B
-
Babikir, H A
A new artificial neural network model integrated with a cat swarm optimization algorithm for predicting the emitted noise during axial piston pump operation [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Badawy, A
Passive vibration attenuation: a comparison study [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
BAlhamaki, A
A new integrated product and process development model [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Barakat, A F
Effect of applying lean maintenance in oil and gas fields [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Bassioni, G
The effect of tire rubber particles on the mechanical and physical properties of polyester [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Belal, H
Experimental investigation of star grains in dual thrust solid propellant motors [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-18]
-
Belal, H
Validation of r elations for the determination of pyrotechnic igniter mass [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Bondok, M M
Test rig design for upper-limb socket prosthetics at transradial amputation level [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
D
-
Darwesh, O
Interactions between microorganisms and composite material with marble & granite filler [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
E
-
Edriys, I I
Abrasive water jet machining of CFRPs: single response optimization using taguchi method optimization [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
El-Agroudy, M N
Assistive exoskeleton hand glove using soft pneumatic actuators: design optimization [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
EL-Desouky, M A
Simulating ultrasonic vibration enhanced FSW process of AA6082 using finite element method [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Elghazaly, S A
Optimizing ladle-refining performance during treating special steel melts for aviation technology [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-8]
-
Elghazaly, W S
Optimizing ladle-refining performance during treating special steel melts for aviation technology [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-8]
-
El-Gindy, M
Handling performance of an 8x8 combat vehicle [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
El-Hadek, M A
Test rig design for upper-limb socket prosthetics at transradial amputation level [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
El-Hofy, H
Ultrasonic-assisted drilling of nickel-based super alloy in conel 601: An experimental study [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Elmaihy, A
Modelling and experimental investigation of high – pressure common rail diesel injection system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Elmaihy, A
Performance of homogeneous charge compression ignition (HCCI) engine with common rail fuel injection [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
El-Naggar, M
Experimental investigation of star grains in dual thrust solid propellant motors [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-18]
-
El-Sallamy, W
Improving water desalination efficiency by using carbon nanotubes as pre-treatment [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
El-Shabasy, A B
Assessment of steel wire's fatigue life using finite elements modelling and experimental testing [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
El-Shabasy, A B
Assessment of St. St. 316L joints welded by laser beam and metal active gas MAG processes [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
El-shamarka, S E
Experimental investigation and numerical simulation of the thermosyphon heat pipe charged with R134a [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Elsheikh, A H
Pre-Cracking techniques of polymeric materials: an overview [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Elsheikh, A H
A new artificial neural network model integrated with a cat swarm optimization algorithm for predicting the emitted noise during axial piston pump operation [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
El-Sheikh, M A
Test rig design for upper-limb socket prosthetics at transradial amputation level [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Elshimy, M
Numerical studies of turbulent premixed flame interaction with repeated solid obstacles [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
El-Wazery, M S
Simulating ultrasonic vibration enhanced FSW process of AA6082 using finite element method [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Emarah, Maya
Design of gain scheduled fuzzy PID controller for multi-link robot manipulators [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-6]
F
-
Farag, S S
Experimental and computational dynamic structural analysis of free-flight rockets [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Fattouh, M
Abrasive water jet machining of CFRPs: single response optimization using taguchi method optimization [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
G
-
Gadallah, N
Optimization of friction stir welding parameters using response surface methodology [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Ghanem, M
Transient heat transfer for GPMG's barrel 7.62x51mm [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-8]
-
Ghoneim, A M
Development of rotary heat exchanger model to investigate performance with integrating controller [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-16]
-
Gyula, K K
Optimizing ladle-refining performance during treating special steel melts for aviation technology [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-8]
H
-
Habaka, M A
Experimental and computational dynamic structural analysis of free-flight rockets [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Hamdi, H M
Design of bio-inspired muscle sarcomere structure using a hybrid hydrogel-IPMC actuator [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Hannora, A E
Phase stability of mechanically alloyed Ti-Fe-Al alloys [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Hasabelnabi, S
Optical non linear characteristics of particles from natural resources [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Hassan, A
Passive vibration damping of acantilever plate [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Hassan, H A
Assessment of steel wire's fatigue life using finite elements modelling and experimental testing [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Hassan, H A
Fracture toughness assessment of axial partially through cracks in X65 and X70 steel pipes [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Hassan, H A
Assessment of St. St. 316L joints welded by laser beam and metal active gas MAG processes [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Hassan, M Nasr
Effect of applying lean maintenance in oil and gas fields [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Hegab, H
Computational fluid dynamic model for machining using minimum quantity coolant [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Hegazy, M
Validation of a simplified model for liquid propellant rocket engine combustion chamber design [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-14]
-
Hegazy, M M
Passive vibration attenuation: a comparison study [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
I
-
Ibrahim, A Z
Penetration of long rods into semi-infinite metallic targets over wide range of impact velocities [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Ibrahim, A Z
Multi-fidelity drag prediction for base bleed projectile [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Ibrahim, A G
Experimental investigation and numerical simulation of the thermosyphon heat pipe charged with R134a [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Ibrahim, S
Numerical studies of turbulent premixed flame interaction with repeated solid obstacles [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Ibrahim, S A
Phase stability of mechanically alloyed Ti-Fe-Al alloys [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Ismail, M A
An experimental study on mechanical and ballistic characteristics of different HTPB composite propellant formulations [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
K
-
Kamal, A
Pre-Cracking techniques of polymeric materials: an overview [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Kamel, Hisham
Evaluating the effect of shape on energy absorbing response of structures used in armored vehicles floors [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-8]
-
Kamel, M
Experimental modal testing of a honeycomb sandwich plate [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Kassem, M
Experimental modal testing of a honeycomb sandwich plate [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Khafagy, A Z
Effect of modified bouc-wen model parameters on the dynamic hysteresis of magnetorheological dampers [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Khalil, A
Optical non linear characteristics of particles from natural resources [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Khalil, M
Experimental and computational dynamic structural analysis of free-flight rockets [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Kishawy, H A
Computational fluid dynamic model for machining using minimum quantity coolant [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Kotb, A T
The effect of rectangular gurney flap on wells turbine performance [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-15]
L
-
Lang, H
Handling performance of an 8x8 combat vehicle [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Liu, Y
A new artificial neural network model integrated with a cat swarm optimization algorithm for predicting the emitted noise during axial piston pump operation [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Lotfy, H M
Assessment of steel wire's fatigue life using finite elements modelling and experimental testing [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Louis, M A
Performance investigation and control parameters choice for sliding mode control of coupled tanks system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-16]
M
-
Mabrouk, M H
Design and manufacturing of a test rig for measuring the torque required in soil drilling operations [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Mabrouk, O M
Simulating ultrasonic vibration enhanced FSW process of AA6082 using finite element method [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Magdy, A M
Assessment of St. St. 316L joints welded by laser beam and metal active gas MAG processes [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Maged, S A
Assistive exoskeleton hand glove using soft pneumatic actuators: design optimization [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Mahmoud, O E
Development of rotary heat exchanger model to investigate performance with integrating controller [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-16]
-
Mahmoud, O E
Performance investigation and control parameters choice for sliding mode control of coupled tanks system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-16]
-
Mahmoud, T S
Study of peak temperatures in friction stir spot welding of AA2024-Al/polycarbonate and AA2024-Al/polypropylene systems [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Makady, A M
Fracture toughness assessment of axial partially through cracks in X65 and X70 steel pipes [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Makled, A
Validation of a simplified model for liquid propellant rocket engine combustion chamber design [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-14]
-
Malalasekera, W
Numerical studies of turbulent premixed flame interaction with repeated solid obstacles [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Masoud, R
Abrasive water jet machining of CFRPs: single response optimization using taguchi method optimization [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Mohamed, A
Passive vibration damping of acantilever plate [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Mohamed, M
Aerodynamic performance improvement using a micro-cylinder as a passive flow control around the S809 airfoil [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Mohammed, R K
Study of peak temperatures in friction stir spot welding of AA2024-Al/polycarbonate and AA2024-Al/polypropylene systems [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Mohammed, S S
Study of peak temperatures in friction stir spot welding of AA2024-Al/polycarbonate and AA2024-Al/polypropylene systems [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Mohany, A
Computational fluid dynamic model for machining using minimum quantity coolant [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Mostafa, W
Aerodynamic performance improvement using a micro-cylinder as a passive flow control around the S809 airfoil [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
N
-
Nawar, M A
The effect of rectangular gurney flap on wells turbine performance [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-15]
-
Nemnem, A F
Experimental modal testing of a honeycomb sandwich plate [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Niklawy, W
Modelling and experimental investigation of high – pressure common rail diesel injection system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Niklawy, W
Performance of homogeneous charge compression ignition (HCCI) engine with common rail fuel injection [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
NourEldin, A F
An experimental study on mechanical and ballistic characteristics of different HTPB composite propellant formulations [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
O
-
Omer, A A
Passive vibration damping of acantilever plate [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Osman, T
Improving water desalination efficiency by using carbon nanotubes as pre-treatment [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
R
-
Rashad, A M
Experimental investigation and numerical simulation of the thermosyphon heat pipe charged with R134a [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Rehan, A
Assistive exoskeleton hand glove using soft pneumatic actuators: design optimization [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Riad, A M
Penetration of long rods into semi-infinite metallic targets over wide range of impact velocities [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Riad, A M
Multi-fidelity drag prediction for base bleed projectile [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Roman, M R
Performance investigation and control parameters choice for sliding mode control of coupled tanks system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-16]
S
-
Sabry, I
Optimization of friction stir welding parameters using response surface methodology [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
-
Said, A E
Fracture toughness assessment of axial partially through cracks in X65 and X70 steel pipes [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
-
Salah, A
Optical non linear characteristics of particles from natural resources [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Salama, A
Validation of r elations for the determination of pyrotechnic igniter mass [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Salem, A M
Effect of modified bouc-wen model parameters on the dynamic hysteresis of magnetorheological dampers [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Sedrak, M F
Performance investigation and control parameters choice for sliding mode control of coupled tanks system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-16]
-
Sedrak, M.
Aerodynamic performance improvement using a micro-cylinder as a passive flow control around the S809 airfoil [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Seleman, M. M
Phase stability of mechanically alloyed Ti-Fe-Al alloys [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Shahin, M
Modelling and experimental investigation of high – pressure common rail diesel injection system [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Shahin, M
Performance of homogeneous charge compression ignition (HCCI) engine with common rail fuel injection [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
-
Shawky, Omar
Simplified algorithm for determining injection duration to achieve fast response in SI engines [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Shiba, M S
Numerical investigations of bistable piezoelectric cantilever for enhanced energy harvesting [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-10]
-
Showaib, E
Pre-Cracking techniques of polymeric materials: an overview [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-9]
-
Sobh, A S
Effect of applying lean maintenance in oil and gas fields [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
T
-
Thévenin, D
Aerodynamic performance improvement using a micro-cylinder as a passive flow control around the S809 airfoil [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
-
Tolbah, F A
Design of bio-inspired muscle sarcomere structure using a hybrid hydrogel-IPMC actuator [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-12]
W
-
Wu, D
A new artificial neural network model integrated with a cat swarm optimization algorithm for predicting the emitted noise during axial piston pump operation [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-7]
Y
-
Youssef, H
Ultrasonic-assisted drilling of nickel-based super alloy in conel 601: An experimental study [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-11]
Z
-
Zakaria, S Y
Experimental investigation and numerical simulation of the thermosyphon heat pipe charged with R134a [Volume 19, 19th International Conference on Applied Mechanics and Mechanical Engineering., 2020, Pages 1-13]
Your query does not match with any item