Number of Articles: 888
A GENERAL PROCEDURE FOR INVESTIGATING THE INSTANTANEOUS KINEMATICS OF MULTI-LOOP MECHANISMS

Volume 1, 2nd Conference on Applied Mechanical Engineering., May 1986, Pages 47-55

10.21608/amme.1986.51800

MAHER GABER MOHAMED

EFFECT OF SHEAR DEFORMATIONS ON THE BENDING OF MODERATELY THICK PLATES

Volume 2, 2nd Conference on Applied Mechanical Engineering., May 1986, Pages 55-63

10.21608/amme.1986.56850

HAMED ABDALLA; KAMAL HASSAN

BASIC CONCEPTS IN liODAL ANALY IS

Volume 1, 1st Conference on Applied Mechanical Engineering., May 1984, Pages 131-140

10.21608/amme.1984.48795

SAAD A. ZAGHLOOL

A NEW METHOD OF DETERMINING THE STRESS INTENSITY FACTOR FROM ISOCHROMATIC FRINGE LOOPS.

Volume 2, 1st Conference on Applied Mechanical Engineering., May 1984, Pages 181-189

10.21608/amme.1984.49589

A. A. Fattah; K. Rajaiah; M. S.C. Bose

Fault monitoring in complex dynamic system by utilization statistical analysis technique

Volume 12, 12th International Conference on Applied Mechanics and Mechanical Engineering., May 2006, Pages 643-658

10.21608/amme.2006.41681

Gomaa F. R.

INVESTIGATIONS ON DAMPING CHARACTERISTICS OF LIQUID COLUMN VIBRATION ABSORBER

Volume 18, 18th International Conference on Applied Mechanics and Mechanical Engineering., April 2018, Pages 1-11

10.21608/amme.2018.34730

M. F. Younes

LOAD DEPENDENT WEAR CHARACTERISTICS OF POLYMER-METAL SLIDING

Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., May 2014, Pages 1-12

10.21608/amme.2014.35502

A. Abdelbary; M. I. El Fahham; M. E. Elnady

OPTIMUM CHOICE OF GAS UNIT GEOMETRICAL CHARACTERISTICS TO ENHANCE ITS EFFICIENCY

Volume 15, 15th International Conference on Applied Mechanics and Mechanical Engineering., May 2012, Pages 1-14

10.21608/amme.2012.36910

M. S. Abo Elkhair

Path Planning of High Speed Manipulators according to Actuator Dynamics

Volume 14, 14th International Conference on Applied Mechanics and Mechanical Engineering., May 2010, Pages 1-15

10.21608/amme.2010.37558

Mohamed H. Mabrouk; Hussien M. Mahgoub

A SURVEY ON THE STRUCTURAL FAILURE ANALYSIS DUE TO IMPACT

Volume 13, 13th International Conference on Applied Mechanics and Mechanical Engineering., May 2008, Pages 47-73

10.21608/amme.2008.38984

IBRAHIM M. A.; YOUNES M. M.; Y. I. EL-SHAER

ANALYSIS OF TRACKED VEHICLES TURNING ON LEVEL TERRAINS

Volume 1, 2nd Conference on Applied Mechanical Engineering., May 1986, Pages 57-68

10.21608/amme.1986.51802

ABDEL MEGID ZIDAN

CREEP BUCKLING OF CYLINDERICAL THIN PANELS

Volume 2, 2nd Conference on Applied Mechanical Engineering., May 1986, Pages 65-72

10.21608/amme.1986.56851

Magdy Adib; H. Ashour

ON THE DYNAMIC ANALYSIS OF A CAM MECHANISM WITH BEARING CLEARANCES

Volume 1, 1st Conference on Applied Mechanical Engineering., May 1984, Pages 141-157

10.21608/amme.1984.48797

B. M. Bahgat; M. O.M. Osman

ANALYSIS OF STEADY STRESSES IN ROTATING ANISOTROPIC DISCS

Volume 2, 1st Conference on Applied Mechanical Engineering., May 1984, Pages 191-200

10.21608/amme.1984.49600

R. A. COOKSON; S. K. SATHIANATHAN

IMPROVEMENT OF TRACTOR SEMITRAILER STABILITY DURING SEVERE MANEUVER AT HIGH SPEED

Volume 12, 12th International Conference on Applied Mechanics and Mechanical Engineering., May 2006, Pages 659-679

10.21608/amme.2006.41682

Elhemly M. A.; Zeyada Y.; Fayed M. A.

FEATURE EXTRACTION ENHANCEMENT BASED ON PARAMETERLESS EMPIRICAL WAVELET TRANSFORM: APPLICATION TO BEARING FAULT DIAGNOSIS

Volume 18, 18th International Conference on Applied Mechanics and Mechanical Engineering., April 2018, Pages 1-19

10.21608/amme.2018.34731

H. H. El-Mongy

SMART MATERIALS USED FOR AERO ENGINE VIBRATION CONTROL

Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., May 2014, Pages 1-20

10.21608/amme.2014.35503

A. M. Morad; A. A. Elzahaby; M. A. Kamel; M. K. Khalil

MODELING OF METALLIZED SOLID FUEL HYBRID PROPULSION SYSTEM

Volume 15, 15th International Conference on Applied Mechanics and Mechanical Engineering., May 2012, Pages 1-22

10.21608/amme.2012.36911

A. E. Makled; H. E. Mostafa; M. A. Al-Sanabawy; M. J. Al-Timimi

Modeling of the Gas and Particle Flow in the Cyclone Separator using LES, RANS and Mathematical Models

Volume 14, 14th International Conference on Applied Mechanics and Mechanical Engineering., May 2010, Pages 1-10

10.21608/amme.2010.37560

Kh. Elsayed; C. Lacor

NON-LINEAR FORCED VIBRATION OF A TAPERED CANTILEVER BEAM

Volume 13, 13th International Conference on Applied Mechanics and Mechanical Engineering., May 2008, Pages 1-11

10.21608/amme.2008.38988

AL-QAISIA A. A.; ABDEL-JABER M. S.

ANALYSIS OF BARREL VIBRATION DURING FIRE

Volume 1, 2nd Conference on Applied Mechanical Engineering., May 1986, Pages 69-80

10.21608/amme.1986.51812

M. S. ABO ELKHAIR; M. ELNAGGAR; A. S. BASSIOUNI

A SIMPLE METHOD FOR DETERMINATION OF THE FRACTURE-MECHANICS GEOMETRIC PARAMETER KI

Volume 2, 2nd Conference on Applied Mechanical Engineering., May 1986, Pages 73-81

10.21608/amme.1986.56864

A. Fattah

A LABORATORY TOOL FOR THE STUDY OF VEHICLE VIBRATION PERFORMANCE

Volume 1, 1st Conference on Applied Mechanical Engineering., May 1984, Pages 159-169

10.21608/amme.1984.48800

S. A. ABOU-EL-SEOUD

EXPERIMENTAL DETERMINATION OF THE STRESSES AND STRAINS IN A THICK PVC CYLINDER REINFORCED BY A STEEL SHELL.

Volume 2, 1st Conference on Applied Mechanical Engineering., May 1984, Pages 201-214

10.21608/amme.1984.49612

Mohamed A. Gaballa; Farouk M.F. Badran

DYNAMIC IMPACT PROBLEMS: MODELING AND ANALYSIS

Volume 12, 12th International Conference on Applied Mechanics and Mechanical Engineering., May 2006, Pages 679-696

10.21608/amme.2006.41683

Elhady A. M.

The International Conference on Applied Mechanics and Mechanical Engineering

Journal Archive