The International Conference on Applied Mechanics and Mechanical Engineering (AMME) - Articles List

Volume & Issue: Volume 12, 12th International Conference on Applied Mechanics and Mechanical Engineering., Spring 2006


1		ACTIVE CONTROL EFFECT ON REDUCING NOISE AND RESONCE AMPLITUDE OF CLAMPED PLATE
	Page 718-724
	Ghazy M. R.; Elhady A. M.
	View Article \| PDF 266.02 K

2		Shock absorber characteristics representations and vehicle performance evaluation
	Page 369-382
	Al-Maqtri M. A.; Hegazy S. A.; Hossamel-deen Y. H.
	View Article \| PDF 3.09 MB

3		SIDE-STICK CONTROL OF POWER RACK AND PINION STEERING SYSTEM
	Page 383-396
	Asfoor M. Sh.; Ebraheem M. H.; El-Haddad M. A.
	View Article \| PDF 563.85 K

4		Evaluation of tracked vehicle performance characteristics
	Page 397-409
	Salem A. M.; Galal W.
	View Article \| PDF 344.69 K

5		RECONSTRUCTION OF DIESEL EGINE CYLINDER PRESSURE USING VIBRATION AND ACOUSTIC EMISSION
	Page 510-525
	Badawi A. B.; A. Elmaihy; Samy A. S.; Shahin M. A.; Mohamed K. I.
	View Article \| PDF 349.03 K

6		EVALUATION OF LOCAL HUMPS AND A NEW HUMP DESIGN
	Page 526-539
	Younes Y. K.; El Demerdash S. M.; S. M., Rabeih El Adl; Hani S. S.
	View Article \| PDF 309.4 K

7		INVESTIGATION OF LATERAL FLYING QUALITIES OF AIRCRAFT
	Page 540-558
	Mohamed T. O.; Bayoumy A. M.; Elshabka A. M.; Ibrahim I. M.
	View Article \| PDF 247.35 K

8		NATURAL FREQUENCIES OF THIN COMPOSITE PLATES SUBJECTED TO STATIC LOADS
	Page 559-572
	Ahmad. S. B.; Raafat. M. G.; Tarek. H. E.; Ahmad. M. S.
	View Article \| PDF 240.01 K

9		ELIMINATION OF UNBALANCE IN MAGNETIC BEARING SYSTEMS WITH NEURO-FUZZY REDUCED ORDER OBSERVER
	Page 573-587
	El Tantawie, M. A.; EL Soaly, E. E.; Hassan, S. S.
	View Article \| PDF 120.04 K

10		SMART FLUID DAMPER MODELS APPLIED TO VEHICLES VIBRATION CONTROL
	Page 588-606
	El-Demerdash S.; El-Butch A.; Rabieh E.; El kafafy M.
	View Article \| PDF 251.17 K

11		AN EXPERIMENTAL INVESTIGATION OF HYDRODYNAMIC DAMPING DUE TO BAFFLE ARRANGEMENTS IN A RECTANGULAR TANK
	Page 607-623
	Younes M. F.; Younes Y. K.; El-Maddah M.; Ibrahim M.; El-Dannanh E. H.
	View Article \| PDF 236.65 K

12		TORSIONAL DYNAMIC OPTIMIZATION OF WIND POWER GENERATORS
	Page 625-642
	KARAM Y. MAALAWI
	View Article \| PDF 555.6 K

13		Fault monitoring in complex dynamic system by utilization statistical analysis technique
	Page 643-658
	Gomaa F. R.
	View Article \| PDF 5.18 MB

14		IMPROVEMENT OF TRACTOR SEMITRAILER STABILITY DURING SEVERE MANEUVER AT HIGH SPEED
	Page 659-679
	Elhemly M. A.; Zeyada Y.; Fayed M. A.
	View Article \| PDF 387.83 K

15		DYNAMIC IMPACT PROBLEMS: MODELING AND ANALYSIS
	Page 679-696
	Elhady A. M.
	View Article \| PDF 209.24 K

16		CRACK DETECTION IN BARS WITH LONGITUDINAL CRACK USING VIBRATION MEASURING TECHNIQUE
	Page 697-717
	Bennaya M.; Mahgoub H. M.; Sherif H. A.
	View Article \| PDF 602.39 K

17		A CRACK PATH-BASED MODEL TO ASSESS MICROSTRUCTURE INCLUSIONS RANDOMNESS
	Page 1-14
	MOHAMED M.A. S.
	View Article \| PDF 230.87 K

18		FATIGUE RESISTANCE OF MAGNESIUM ALLOY AZ 91D AT HIGH-FREQUENCY CYCLE LOADING.
	Page 15-21
	KUFFOVA M.
	View Article \| PDF 1.31 MB

19		FINE GRAINED 6061 ALUMINUM ALLOY SHEETS PRODUCED BY ACCUMULATIVE ROLL- BOUNDING (ARB) PROCESS.
	Page 22-34
	EL SEAIDY M. I.; IBRAHIM M. M.; GHONEIM M. M.
	View Article \| PDF 1.78 MB

20		THE MECHANICAL BEHAVIOUR OF RECYCLED HIGH DENSITY POLYETHYLENE
	Page 35-50
	Ali A. A.; Abo El-Khair M. S.
	View Article \| PDF 3.35 MB

21		THE QUALITY OF AL-SI CASTING OF L SECTION USING WILLIAM′S CORE AND ELLIPTICAL AND SPHERICAL RISERS
	Page 51-68
	IBRAHIM M.; ISKANDER B. A.; MOHIE M.
	View Article \| PDF 4.09 MB

22		WINDING ANGLE EFFECT ON FRATURE BEHAVIOUR OF COMPOSITE TUBES UNDER DIFFERENT LOADING CONDITIONS
	Page 69-80
	El-Wahab M. M.; El-Soaly E. E.; El-Kader M. S.; Daken M. H.
	View Article \| PDF 5.73 MB

23		STUDY OF THE MECHANICAL AND METALLOGRAPHIC PROPERTIES OF CARBON-ALUMINA COATED IRON PRODUCED BY IMPULSE PLASMA DEPOSITION
	Page 81-91
	RASHAD M. M.; MASOUD M. M.; HASSAN M. F.; OSMAN M. M.
	View Article \| PDF 1.08 MB

24		DESIGN ALTERNATIVES FOR A MULTI-STANDARD MACHINE
	Page 410-420
	Mohamed M.A. S.
	View Article \| PDF 154.99 K

25		DESIGN AND MANUFACTURING OF NEW UNWEIGHING SYSTEM.
	Page 421-431
	Omer A. A.; Elshaer Y. I.
	View Article \| PDF 1.05 MB

26		METHODOLOGY OF OBTAINING STRUCTURAL MODEL OVER A MONOCOQUE CLOSED INTEGRAL SEDAN CAR BODY STRUCTURE
	Page 432-445
	Ahmed A. K.; Mohamed A. M.; Metwally M. M.; Mokhtar M. E.
	View Article \| PDF 3.39 MB

27		SEPARATION AND IDENTIFICATION OF SIMULATED DIESEL ENGINE NOISE USING INDEPENDENT COMPONENTANALYSIS AND TIME-FREQUENCYANALYSIS
	Page 264-281
	Badawi A. B.; A. Elmaihy; Samy A. S.; Shahin M. A.; Mohamed K. I.
	View Article \| PDF 391.45 K

28		DIESEL ENGINE MISFIRE DETECTION UTILIZING TIME-FREQUENCY ANALYSIS OF MEASURED ENGINE VIBRATION
	Page 282-297
	Badawi A. B.; A. Elmaihy; Samy A. S.; Shahin M. A.; Mohamed K. I.
	View Article \| PDF 798.52 K

29		EFFECT OF PIPE INCLINATION AND ADDING FINES ON SLURRY TRANSPORT OF COARSE PARTICLES.
	Page 298-314
	Fangary Y. S.; Mahmoud N. A.
	View Article \| PDF 223.86 K

30		INVESTIGATION OF STATIC AND DYNAMIC BEHAVIOUR OF PREESURE COMPENSATED VARIABLE DISPLACEMENT SWASH PLATE AXAL PISTON PUMP
	Page 315-333
	Tamer A. SALEH; M. Galal RABIE; S. E. ABDOU
	View Article \| PDF 5.57 MB

31		DYNAMIC PERFORMANCE OF AN ELECTROHYDRAULIC SERVO ACTUATOR WITH CONTACTLESS CONTROLLED SPOOL
	Page 334-351
	M. Metwally; G. Rabie; N. Girgis; I. Saleh
	View Article \| PDF 1.63 MB

32		HEAT TRANSFER ENHANCEMENT IN PIPE FLOW WITH DOWNSTREAM PULSATION
	Page 352-368
	A. R. El-shamy; R. I. Afify; S. A. Abdel-Moneim; H. A. Refaey
	View Article \| PDF 2.82 MB

33		STUDYING THE PARAMETERS INFLUENCING THE ACCURACY OF ELECTRON BEAM DERILLED HOLES
	Page 202-213
	ELNAGGAR W. M.; KOHAIL A. M.; MOUGHITH W. S.
	View Article \| PDF 297.87 K

34		OPTIMIZATION OF IDLE PATH IN DRILLING ON CNC MACHINING CENTRE USING THE GA
	Page 214-228
	Abd Elkhalek Sh. M.; Elhakim M. A.; Wahba W. A.; Moughith W. S.
	View Article \| PDF 315.1 K

35		THE INFLUENCE OF LASER ASSISTED TURNING PARAMETERS ON CUTTING FORCES-NEW APPROACH
	Page 229-238
	BAKER M. H.; YOSSEF A.M. F.; KHOAIL A. M.; MOUGHITH W. M.
	View Article \| PDF 13.68 MB

36		DETERMINATION OF MACHINING PROCESS FOR ROTATIONAL PARTS USING NEURAL NETWORKS
	Page 239-251
	EL-AGAMY M. S.; MOHAMMED A. AWAD
	View Article \| PDF 418.88 K

37		A SAFETY PLAN FOR AN INDUSTRIAL PLANT
	Page 252-263
	Ramadan M. R.; Mohamed M.A. S.; Assar A.; Risha H. A.
	View Article \| PDF 112.26 K

38		DESIGN OF AN EXPLOSIVELY FORMED PENETRATOR CAPABLE OF DEFEATING A SPECIFIC METALLIC TARGET
	Page 446-466
	A. M. Riad; M. M. Ismail; E. A. Ibrahim
	View Article \| PDF 939.92 K

39		DYNAMIC BEHAVIOR OF CONTROL VALVES OF A LIQUID ROCKET ENGINE FEEDING SYSTEM
	Page 467-489
	Tamer N. MAHMOUD; M. Galal RABIE; M. Allam EL-SENBAWI
	View Article \| PDF 533.8 K

40		BALLISTIC RESISTANCE OF FLEXIBLE COMPOSITE AND TEXTILE TARGETS
	Page 490-509
	E. Elawad; A. Fayed; M. S. Abdelkader
	View Article \| PDF 599.97 K

41		MECHANICAL CRITERIA FOR REPORTS TO OPTIMALLY JUMP AND RUN
	Page 144-164
	MOHAMED M.A. S.
	View Article \| PDF 306.89 K

42		THEORETICAL AND EXPERIMENTAL INVESTIGATIONS OF DYNAMIC BEHAVIOR OF AN ELECTRO-HYDRAULIC DIRECTIONAL PROPORTIONAL VALVE
	Page 165-177
	MENSHAWY T. M.; LOTFY A. H.
	View Article \| PDF 5.24 MB

43		CONDITION MONITORING AND CONTROL OF ROLLING MILLS USING ELECTRO-HYDRAULIC SYSTEM
	Page 178-201
	KHALIL M. K.; DEPING LI M. E.; BHAT R. B.
	View Article \| PDF 771.51 K

44		EXPLORATORY STUDY OF THE BEHAVIOR OF SOME LOCAL AGRICULTURAL RESIDUAL MATERIALS TO BE USED FOR REINFORCING CONSTRUCTION MATERIALS
	Page 92-111
	Sharkawi A. M.; Showaib E. A.
	View Article \| PDF 9.06 MB

45		AN INVESTIGATION OF THE INSERTIONMECHANISM INFLUENCE ON THE OVERALL BEHAVIOR OF THE THREE-DIMENSIONAL AEROSPACE COMPONENTS
	Page 1-8
	Tawfic T. M.
	View Article \| PDF 127.25 K

46		AN IMPROVEMENT OF LONGITUDINAL FLYING QUALITY OF HSCT AEROELASTIC AIRCRAFT MODEL USING GPC TECHNIQUE
	Page 128-143
	ABDELHADY M. E.; AMGAD M. B.; GAMAL M. E.
	View Article \| PDF 457.38 K