A
-
Abbas, M. S.
FEATURE RECOGNITION TECHNIQUE FOR MILLING OPERATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Abbas, M. S.
COMPUTER AIDED PROCESS PLANNING FOR PRISMATIC PARTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Abbas, M. K.
MODELING AND ANALYSIS OF SHAPE MEMORY ALLOY LAMINATED COMPOSITE PLATES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-30]
-
Abdalla, H. M.
3-D NUMERICAL STUDY OF THE EFFECT OF IMPELLER BLADES SLOT ON THE CENTRIFUGAL PUMP PERFORMANCE USING CFD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Abdallah, A. S.
EFFECT OF ALLOY COMPOSITION ON THE MECHANICAL PROPERTIES AND FRACTURE BEHAVIOR OF TUNGSTEN HEAVY ALLOYS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Abd Allah, A. A.
DYNAMIC SIMULATION OF TANK GUN RECOIL CYCLE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Abdelbary, A.
LOAD DEPENDENT WEAR CHARACTERISTICS OF POLYMER-METAL SLIDING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Abdelbary, B. M.
ELECTRICAL CONDUCTIVITY AND DIELECTRIC CONSTANT OF HOT PRESSED MWCNTs/ CARBON NANO FIBRIL COMPOSITE PAPER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Abdelbary, E. M.
PREPARATION AND CHARACTERIZATION OF YTTRIA–CERIA DOPED TETRAGONAL ZIRCONIA / ALUMINA COMPOSITES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
AbdELbaset, H.
INVESTIGATION OF THE DISPERSION OF UNGUIDED FINNED MISSILE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Abdel-Hamid, O. E.
EFFECT OF BASE BLEED DIMENSIONS ON THE BALLISTIC PERFORMANCE OF ARTILLERY PROJECTILES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Abdel-Karim, M.
OPTIMIZATION FOR HIERARCHICAL PRODUCTION PLANNING OF INDUSTRIAL PROCESSES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Abdellatif, O. E.
NUMERICAL INVESTIGATION OF VENTILATION SYSTEMS TO CONTROL INFECTION INSIDE OPERATING ROOMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Abd-Elmalak, T.
AN EXPERIMENTAL STUDY OF DESICCANT WHEEL-AIR HUMIDIFIER INTEGRATION IN HOT AND DRY CLIMATES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Abdel-Meguid, M. E.
A MICROMECHANICS-BASED DAMAGE DIAGNOSTIC MODEL FOR MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Abdel-Meguid, M. E.
A MULTISCALE-BASED MODEL FOR COMPOSITE MATERIALS WITH EMBEDDED PZT FILAMENTS FOR ENERGY HARVESTING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Abdel-Raheem, M. A.
NUMERICAL MODELING OF HYDROGEN PREMIXED COMBUSTION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Abdel Razek, S. M.
CORN AND SOYBEAN BIODIESEL BLENDS AS ALTERNATIVE FUELS FOR DIESEL ENGINES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Abdelsalam, O. R.
IMPROVEMENT OF RESIDUAL STRESSES IN THICK WALL CYLINDERS USING MULTIPLE AUTOFRETTAGE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Abdou, G.
EFFECT OF ALLOY COMPOSITION ON THE MECHANICAL PROPERTIES AND FRACTURE BEHAVIOR OF TUNGSTEN HEAVY ALLOYS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Abdulkarim, J. M.
INVESTIGATION OF PREMIXED COMBUSTION PROPERTIES OF GASEOUS FUEL (LPG, PROPANE, AND BUTANE) IN TUBULAR BURNER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-22]
-
Abdulla, M. M.
ANALYSIS OF A LIGHT AIRCRAFT RESPONSE TO GUST WIND BASED ON NONLINEAR MODEL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Abo El-Azm, A. S.
3-D NUMERICAL STUDY OF THE EFFECT OF IMPELLER BLADES SLOT ON THE CENTRIFUGAL PUMP PERFORMANCE USING CFD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Abou El-Azm, A. S.
EXPERIMENTAL STUDY OF LEAKAGE COMPENSATION ON DYNAMIC CHARACTERISTICS OF HYDRAULIC POWER SYSTEMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Abou-Elela, H. A.
EFFECT OF BASE BLEED DIMENSIONS ON THE BALLISTIC PERFORMANCE OF ARTILLERY PROJECTILES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Abouobaia, E.
ANALYTICAL INVESTIGATIONS OF THE GRAVITY EFFECT ON THE DYNAMICS AND PERFORMANCE OF CENTRIFUGAL PENDULUM VIBRATION ABSORBER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Abu-Elyazeed, O. S.
IGNITION DELAY OF JOJOBA BIO-DIESEL AND ITS BLENDS WITH GAS OIL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Abu El-Yazeed, O. S. M.
A COMPUTATIONAL STUDY OF IN-CYLINDER FLOW CHARACTERISTICS IN TWO STROKE SIE WITH DOUBLE INTAKE MANIFOLDS AT DIFFERENT INCLINATION ANGLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Afefy, I. H.
OPTIMIZATION FOR HIERARCHICAL PRODUCTION PLANNING OF INDUSTRIAL PROCESSES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Afifi, A. A.
FEATURE RECOGNITION TECHNIQUE FOR MILLING OPERATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Afifi, A. A.
COMPUTER AIDED PROCESS PLANNING FOR PRISMATIC PARTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Afify, R. I.
NUMERICAL INVESTIGATION OF VENTILATION SYSTEMS TO CONTROL INFECTION INSIDE OPERATING ROOMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Ahmed, S. A.
EVALUATION OF SHAPED CHARGE PERFORMANCE UNDER ITS VARIABLE FACTORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Ajala, M. R.
MODELING STRESS OF SMART BEAM WITH THERMO-PIEZOELECTRIC EFFECTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Ali, A. M.
MODELING AND SIMULATION OF HYBRID ELECTRIC VEHICLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Ali, A. A.
ELECTRICAL CONDUCTIVITY AND DIELECTRIC CONSTANT OF HOT PRESSED MWCNTs/ CARBON NANO FIBRIL COMPOSITE PAPER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Ali, A. A.
HOT-PRESSED ELECTROSPUN MWCNTs/CARBON NANO FIBRIL COMPOSITES: POTENTIAL APPLICATIONS FOR BREAKING PADS AND JOURNAL BEARING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Ali, N.
INVESTIGATION OF CRITICAL LEAN CULTURE CRITERIA FRAMEWORK FOR LEAN TRANSFORMATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Ali, N.
DEVELOPMENT OF LEAN CULTURE ASSESSMENT FOR LEAN MANUFACTURING IMPLEMENTATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Aljinaidi, A. A.
DEVELOPMENT OF CFRE COMPOSITE JOINTS USING MWCNT/E ADHESIVES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-22]
-
Alsanabawy, M. A.
INVESTIGATION OF THE DISPERSION OF UNGUIDED FINNED MISSILE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Alves, M.
DETERMINING MATERIAL CONSTITUTIVE PARAMETERS ON STEEL SHEETS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-15]
-
Al Wardany, A. M.
AN INVESTIGATION INTO THE EFFECT OF CNC-EDM WIRE CUTTING PARAMETERS FOR CROSS-FEED TURNING PROCESS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Anbr, S.
HEAT TRANSFER CHARACTERISTICS OF WATER FLOWING THROUGH SINGLE AND DOUBLE STACK RECTANGULAR MICROCHANNELS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Arafa, N.
AEROACOUSTIC RESPONSE OF ISOLATED CYLINDER(S) IN CROSS-FLOW AT DIFFERENT LOCATIONS INSIDE A RECTANGULAR DUCT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Asfoor, M. S.
USE OF GT-SUITE TO STUDY PERFORMANCE DIFFERENCES BETWEEN INTERNAL COMBUSTION ENGINE (ICE) AND HYBRID ELECTRIC VEHICLE (HEV) POWERTRAINS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Attai, Y. A.
IGNITION DELAY OF JOJOBA BIO-DIESEL AND ITS BLENDS WITH GAS OIL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Awaad, M.
PREPARATION AND CHARACTERIZATION OF YTTRIA–CERIA DOPED TETRAGONAL ZIRCONIA / ALUMINA COMPOSITES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Ayad, A. F.
3-D NUMERICAL STUDY OF THE EFFECT OF IMPELLER BLADES SLOT ON THE CENTRIFUGAL PUMP PERFORMANCE USING CFD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
B
-
Badawy, A.
DYNAMIC MODEL AND ANALYSIS OF A HEXAPOD ROBOT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Bahei El-Din, Y. A.
A MICROMECHANICS-BASED DAMAGE DIAGNOSTIC MODEL FOR MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Bahei-El-Din, Y. A.
A MULTISCALE-BASED MODEL FOR COMPOSITE MATERIALS WITH EMBEDDED PZT FILAMENTS FOR ENERGY HARVESTING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Bahr, M. K.
LAYOUT OF GRADUATE-LEVEL FLUID POWER RESEARCH LAB. [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Bakkar, A.
SURFACE MECHANICAL ATTRITION TREATMENT OF COMMERCIALLY PURE TITANIUM VT1-0 [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Bakr, M.
NONLINEAR FINITE ELEMENT MODELING OF CRYSTALLINE MICROSTRUCTURAL PROPERTIES WITH APPLICATION TO ALUMINUM ALLOYS FOR MODERN ARMORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Barakat, A. F.
ARTIFICIAL INTELLIGENCE CO-OPERATION WITH CONVENTIONAL METHODOLOGIES FOR CONTROLLING OVER WEAR [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Bedir, F.
EXPERIMENTALLY INVESTIGATING THE BALLISTIC PROPERTIES OF THE POLYMER-MATRIXED LAYERED AND FIBERREINFORCED COMPOSITE MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Belal, T. M.
NUMERICAL INVESTIGATION OF VENTILATION SYSTEMS TO CONTROL INFECTION INSIDE OPERATING ROOMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Belal, T. M.
NUMERICAL STUDY ON THE EFFECT OF SECONDARY AIR INLET CONDITIONS ON A GAS TURBINE COMBUSTOR BURNING NATURAL GAS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Beyerlein, S.
USE OF GT-SUITE TO STUDY PERFORMANCE DIFFERENCES BETWEEN INTERNAL COMBUSTION ENGINE (ICE) AND HYBRID ELECTRIC VEHICLE (HEV) POWERTRAINS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Bhat, R.
ANALYTICAL INVESTIGATIONS OF THE GRAVITY EFFECT ON THE DYNAMICS AND PERFORMANCE OF CENTRIFUGAL PENDULUM VIBRATION ABSORBER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Brenn, G.
NUMERICAL STUDY FOR SHAPE OSCILLATION OF FREE VISCOELASTIC DROP USING THE ARBITRARY LAGRANGIAN EULERIAN METHOD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
But, A.
THE MANUFACTURING OPTIMIZATION ON CNC MACHINE TOOLS USING CORRECT MILLING STRATEGIES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-2]
C
-
Calle, M. A.G.
DETERMINING MATERIAL CONSTITUTIVE PARAMETERS ON STEEL SHEETS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-15]
-
Cidek, M. F.
AN EXPERIMENTAL STUDY OF DESICCANT WHEEL-AIR HUMIDIFIER INTEGRATION IN HOT AND DRY CLIMATES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
D
-
Darwish, S. H.
A PROPOSED METHOD FOR DETECTING THE CHAOTIC BEHAVIOUR IN DYNAMICAL SYSTEMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Das, P. K.
EXPERIMENTAL STUDIES ON HYDRODYNAMIC CHARACTERISTICS OF A VERTICAL PLUNGING LIQUID JET SYSTEM [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Duraia, E. M.
SURFACE MECHANICAL ATTRITION TREATMENT OF COMMERCIALLY PURE TITANIUM VT1-0 [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
E
-
El-Afandi, G.
WIND ENERGY MODELING OVER WEST AFRICA [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
El-Anwar, M. I.
DESIGN OF HYDROGEN STORAGE TANKS FABRICATED FROM COMPOSITE MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-7]
-
Elassal, A. M.
USING COMPUTER SIMULATION IN LEAN MANUFACTURING IMPLEMENTATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-25]
-
Elbadawy, I.
A COMPUTATIONAL STUDY OF IN-CYLINDER FLOW CHARACTERISTICS IN TWO STROKE SIE WITH DOUBLE INTAKE MANIFOLDS AT DIFFERENT INCLINATION ANGLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Elbadawy, I.
HEAT TRANSFER CHARACTERISTICS OF WATER FLOWING THROUGH SINGLE AND DOUBLE STACK RECTANGULAR MICROCHANNELS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
El Bayoumi, G. M.
CONTROL OF UNDERACTUATED ACROBOT SYSTEM USING PARTIAL FEEDBACK LINEARIZATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
El-Chazly, N. M.
DESIGN OF HYDROGEN STORAGE TANKS FABRICATED FROM COMPOSITE MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-7]
-
Eldesouky, A. R.
HOT-PRESSED ELECTROSPUN MWCNTs/CARBON NANO FIBRIL COMPOSITES: POTENTIAL APPLICATIONS FOR BREAKING PADS AND JOURNAL BEARING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Eldreny, W.
DYNAMIC MODEL AND ANALYSIS OF A HEXAPOD ROBOT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
El-Etriby, A. E.
A MULTISCALE-BASED MODEL FOR COMPOSITE MATERIALS WITH EMBEDDED PZT FILAMENTS FOR ENERGY HARVESTING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Elewa, M. T.
MICROSTRUCTURAL MODELING OF INTRINSIC STRESSES IN MULTI-JUNCTION BASED PHOTOVOLTAIC [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-7]
-
El Fahham, M. I.
LOAD DEPENDENT WEAR CHARACTERISTICS OF POLYMER-METAL SLIDING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
El-Gindy, M.
CONTROL STRATEGY DEVELOPMENT FOR INDEPENDENT WHEEL TORQUE DISTRIBUTION FOR MULTI-WHEELED COMBAT VEHICLE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
El-Gohary, A. M.
AEROELASTIC OPTIMIZATION OF FUNCTIONALLY GRADED WINGS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-19]
-
ElKhodary, K.
MATERIALS BY DESIGN: FROM THE NANOSCIENCE TO THE MACROMECHANICS OF MODERN ARMOR MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
ElKhodary, K.
NONLINEAR FINITE ELEMENT MODELING OF CRYSTALLINE MICROSTRUCTURAL PROPERTIES WITH APPLICATION TO ALUMINUM ALLOYS FOR MODERN ARMORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
El-Labban, H. F.
GRAIN REFINEMENT OF ALUMINUM-BASED NANOCOMPOSITES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
El-Labban, H. F.
MODIFICATION OF A SURFACE LAYER MICROSTRUCTURE FOR NODULAR CAST IRON USING CO2 LASER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
El-Maghraby, H. F.
PREPARATION AND CHARACTERIZATION OF YTTRIA–CERIA DOPED TETRAGONAL ZIRCONIA / ALUMINA COMPOSITES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
El-Mahallawi, I. S.
EFFECT OF POURING TEMPERATURE AND WATER COOLING ON THE MICROSTRUCTURE OF INGOTS PRODUCED BY COOLING SLOPE CASTING TECHNIQUE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Elmas, U.
EXPERIMENTALLY INVESTIGATING THE BALLISTIC PROPERTIES OF THE POLYMER-MATRIXED LAYERED AND FIBERREINFORCED COMPOSITE MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Elnady, M. E.
LOAD DEPENDENT WEAR CHARACTERISTICS OF POLYMER-METAL SLIDING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Elnashar, G.
DYNAMIC MODEL AND ANALYSIS OF A HEXAPOD ROBOT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
El-Saady, W. M.
DYNAMIC SIMULATION OF TANK GUN RECOIL CYCLE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Elsayed, K.
2D VISCOUS SHAPE DESIGN OPTIMIZATION AND MESH ADAPTATION USING THE ADJOINT METHOD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Elsayed, K.
OPTIMIZATION OF MULTI-FIDELITY DATA USING CO-KRIGING FOR HIGH DIMENSIONAL PROBLEMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-25]
-
Elshafei, M. Adnan
MODELING STRESS OF SMART BEAM WITH THERMO-PIEZOELECTRIC EFFECTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Elshafei, M. A.
MODELING AND ANALYSIS OF SHAPE MEMORY ALLOY LAMINATED COMPOSITE PLATES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-30]
-
Elshenawy, T.
A MODIFIED VIRTUAL ORIGIN MODEL FOR SHAPED CHARGE JET PENETRATION WITH NON-UNIFORM DENSITY DISTRIBUTION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
EL-Soaly, E. E.
DETECTION OF STRESS STATE IN A PRESSURIZED THICK– WALLED CYLINDER BY MEASURING STRAINS ON ANNULAR PLATE SURFACE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Eltabey, M. M.
ELECTRICAL CONDUCTIVITY AND DIELECTRIC CONSTANT OF HOT PRESSED MWCNTs/ CARBON NANO FIBRIL COMPOSITE PAPER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Elzahaby, A. A.
SMART MATERIALS USED FOR AERO ENGINE VIBRATION CONTROL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Elzahaby, A. A.
ENHANCEMENT OF PROPULSION PERFORMANCE THROUGH JET NOISE REDUCTION TECHNOLOGIES: A REVIEW [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Emarah, M. M.
CONTROL OF UNDERACTUATED ACROBOT SYSTEM USING PARTIAL FEEDBACK LINEARIZATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Etman, M.
ARTIFICIAL INTELLIGENCE CO-OPERATION WITH CONVENTIONAL METHODOLOGIES FOR CONTROLLING OVER WEAR [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
F
-
Farag, A. I.
NUMERICAL STUDY ON THE EFFECT OF SECONDARY AIR INLET CONDITIONS ON A GAS TURBINE COMBUSTOR BURNING NATURAL GAS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Fatouh, M.
HEAT TRANSFER CHARACTERISTICS OF WATER FLOWING THROUGH SINGLE AND DOUBLE STACK RECTANGULAR MICROCHANNELS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Fayed, A. I.
EFFECT OF ALLOY COMPOSITION ON THE MECHANICAL PROPERTIES AND FRACTURE BEHAVIOR OF TUNGSTEN HEAVY ALLOYS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
G
-
Gaafer, A. M.
EFFECT OF POURING TEMPERATURE AND WATER COOLING ON THE MICROSTRUCTURE OF INGOTS PRODUCED BY COOLING SLOPE CASTING TECHNIQUE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Gad, M. M.
A COMPUTATIONAL STUDY OF IN-CYLINDER FLOW CHARACTERISTICS IN TWO STROKE SIE WITH DOUBLE INTAKE MANIFOLDS AT DIFFERENT INCLINATION ANGLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Ghorbaniasl, G.
2D VISCOUS SHAPE DESIGN OPTIMIZATION AND MESH ADAPTATION USING THE ADJOINT METHOD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Gonzales, M. A. Calle
STRUCTURAL IMPACT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
H
-
Hamed, M. A.
DEVELOPMENT OF CFRE COMPOSITE JOINTS USING MWCNT/E ADHESIVES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-22]
-
Hannora, A. E.
SURFACE MECHANICAL ATTRITION TREATMENT OF COMMERCIALLY PURE TITANIUM VT1-0 [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Hassan, M.
AEROACOUSTIC RESPONSE OF ISOLATED CYLINDER(S) IN CROSS-FLOW AT DIFFERENT LOCATIONS INSIDE A RECTANGULAR DUCT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Hassan, R. M.
WIND ENERGY MODELING OVER WEST AFRICA [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Hassan, T. M.
ANALYSIS OF A LIGHT AIRCRAFT RESPONSE TO GUST WIND BASED ON NONLINEAR MODEL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Hatem, T. M.
MATERIALS BY DESIGN: FROM THE NANOSCIENCE TO THE MACROMECHANICS OF MODERN ARMOR MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Hatem, T. M.
MICROSTRUCTURAL MODELING OF INTRINSIC STRESSES IN MULTI-JUNCTION BASED PHOTOVOLTAIC [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-7]
-
Hatem, T. M.
A MICROMECHANICS-BASED DAMAGE DIAGNOSTIC MODEL FOR MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Hatem, T. M.
A MULTISCALE-BASED MODEL FOR COMPOSITE MATERIALS WITH EMBEDDED PZT FILAMENTS FOR ENERGY HARVESTING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Hegazi, M.
DYNAMIC MODEL AND ANALYSIS OF A HEXAPOD ROBOT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Hegazy, S. A.
MODELING AND SIMULATION OF HYBRID ELECTRIC VEHICLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Helal, M.
USING COMPUTER SIMULATION IN LEAN MANUFACTURING IMPLEMENTATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-25]
-
Hua, C. G.
A NEW CONCEPT FOR THE LINE OF SIGHT STABILIZATION “BALL STABILIZATION” [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-15]
-
Hussien, A. H.
DYNAMIC SIMULATION OF TANK GUN RECOIL CYCLE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
I
-
Ibrahim, A. Z.
DYNAMIC SIMULATION OF TANK GUN RECOIL CYCLE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Ibrahim, A. Z.
EVALUATION OF SHAPED CHARGE PERFORMANCE UNDER ITS VARIABLE FACTORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Ibrahim, A. Z.
EFFECT OF BASE BLEED DIMENSIONS ON THE BALLISTIC PERFORMANCE OF ARTILLERY PROJECTILES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Ibrahim, M. K.
CONTROL OF UNDERACTUATED ACROBOT SYSTEM USING PARTIAL FEEDBACK LINEARIZATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Ibrahim, R. A.
MODELING OF DYNAMIC SYSTEMS WITH VIBRO-IMPACT INTERACTION AND DISCONTINUITY MAPPING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Ibrahim, S. S.
NUMERICAL MODELING OF HYDROGEN PREMIXED COMBUSTION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Ibrayev, A. G.
TRANSVERSE OSCILLATION OF THE RAIL WHICH LIES ON THE DISCRETE BASE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-8]
-
Ismael, K. T.
MULTI OBJECTIVE OPTIMIZATION OF PRESSURE CYCLE OF ABS INJECTION MOLDING PROCESS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
J
-
Jang, H. L.
CONCEPT, THEORY, DESIGN AND EXPERIMENTAL TESTS OF SELFPOWERED LUBRICATION IN CERAMIC COMPOSITE AND ROTORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
K
-
Kamel, B. M.
DESIGN OF HYDROGEN STORAGE TANKS FABRICATED FROM COMPOSITE MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-7]
-
Kamel, H. M.
MODELING AND SIMULATION OF HYBRID ELECTRIC VEHICLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Kamel, M. A.
SMART MATERIALS USED FOR AERO ENGINE VIBRATION CONTROL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Khalil, M. K.
SMART MATERIALS USED FOR AERO ENGINE VIBRATION CONTROL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Khalil, M. K.
ENHANCEMENT OF PROPULSION PERFORMANCE THROUGH JET NOISE REDUCTION TECHNOLOGIES: A REVIEW [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Khashaba, U. A.
DEVELOPMENT OF CFRE COMPOSITE JOINTS USING MWCNT/E ADHESIVES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-22]
-
Kim, J. H.
CONCEPT, THEORY, DESIGN AND EXPERIMENTAL TESTS OF SELFPOWERED LUBRICATION IN CERAMIC COMPOSITE AND ROTORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Kinawy, M. A.
AN EXPERIMENTAL STUDY OF DESICCANT WHEEL-AIR HUMIDIFIER INTEGRATION IN HOT AND DRY CLIMATES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Kishawy, H. A.
CONTROL STRATEGY DEVELOPMENT FOR INDEPENDENT WHEEL TORQUE DISTRIBUTION FOR MULTI-WHEELED COMBAT VEHICLE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Koura, O. M.
VIRTUAL ROLLING GEAR TESTING MACHINE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
L
-
Lacor, C.
2D VISCOUS SHAPE DESIGN OPTIMIZATION AND MESH ADAPTATION USING THE ADJOINT METHOD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Lacor, C.
OPTIMIZATION OF MULTI-FIDELITY DATA USING CO-KRIGING FOR HIGH DIMENSIONAL PROBLEMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-25]
M
-
Maalawi, K. Y.
AEROELASTIC OPTIMIZATION OF FUNCTIONALLY GRADED WINGS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-19]
-
Mahdy, M. A.
AN INVESTIGATION INTO THE EFFECT OF CNC-EDM WIRE CUTTING PARAMETERS FOR CROSS-FEED TURNING PROCESS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Mahmoud, A. A.
OPTIMIZATION FOR HIERARCHICAL PRODUCTION PLANNING OF INDUSTRIAL PROCESSES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Mahmoud, F. H.
EFFECT OF POURING TEMPERATURE AND WATER COOLING ON THE MICROSTRUCTURE OF INGOTS PRODUCED BY COOLING SLOPE CASTING TECHNIQUE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Mahmoud, O. K.
INVESTIGATION OF THE DISPERSION OF UNGUIDED FINNED MISSILE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Mahmoud, O. K.
EFFECT OF BASE BLEED DIMENSIONS ON THE BALLISTIC PERFORMANCE OF ARTILLERY PROJECTILES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Mahmoud, T. S.
EFFECT OF POURING TEMPERATURE AND WATER COOLING ON THE MICROSTRUCTURE OF INGOTS PRODUCED BY COOLING SLOPE CASTING TECHNIQUE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Maiti, B.
EXPERIMENTAL STUDIES ON HYDRODYNAMIC CHARACTERISTICS OF A VERTICAL PLUNGING LIQUID JET SYSTEM [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Malalasekera, W.
NUMERICAL MODELING OF HYDROGEN PREMIXED COMBUSTION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-10]
-
Mamatova, G. U.
MOTION OF AN AXISYMMETRIC RIGID BODY WITH VARIABLE INERTIA MOMENTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-8]
-
Marian, R.
THE MANUFACTURING OPTIMIZATION ON CNC MACHINE TOOLS USING CORRECT MILLING STRATEGIES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-2]
-
Merdan, M.
MULTI OBJECTIVE OPTIMIZATION OF PRESSURE CYCLE OF ABS INJECTION MOLDING PROCESS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Miranda, J.
2D VISCOUS SHAPE DESIGN OPTIMIZATION AND MESH ADAPTATION USING THE ADJOINT METHOD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Mohamed, A. A.
A PROPOSED METHOD FOR DETECTING THE CHAOTIC BEHAVIOUR IN DYNAMICAL SYSTEMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Mohamed, A. E.
ADVANCED STUDIES ON PLUTONIUM FOR PU ISOTOPE TRANSMUTATION AND PU SEPARATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-6]
-
Mohamed, A. E.
PLUTONIUM USAGE AND MANAGEMENT IN PWR AND COMPUTING AND PHYSICAL METHODS TO CALCULATE PU [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Mohamed, A. E.
SECURE FACILITIES FOR NUCLEAR WARHEADS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Mohamed, A. E.
EGYPTIAN NUCLEAR ACTIVITIES AT RESEARCH REACTORS , LABORATORIES, AND URANIUM PRODUCTION (INDEPENDENT REVIEW) [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-2]
-
Mohamed, F. A.
DEFORMATION MECHANISM IN NANOCRYSTALLINE MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-1]
-
Mohamed, H. E.
NUMERICAL INVESTIGATION OF VENTILATION SYSTEMS TO CONTROL INFECTION INSIDE OPERATING ROOMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Mohany, A.
AEROACOUSTIC RESPONSE OF ISOLATED CYLINDER(S) IN CROSS-FLOW AT DIFFERENT LOCATIONS INSIDE A RECTANGULAR DUCT [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Mokbel, H. F.
A NEW CONCEPT FOR THE LINE OF SIGHT STABILIZATION “BALL STABILIZATION” [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-15]
-
Morad, A. M.
SMART MATERIALS USED FOR AERO ENGINE VIBRATION CONTROL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Morad, A. M.
NICKEL BASE SUPERALLOYS USED FOR AERO ENGINE TURBINE BLADES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-22]
-
Morgan, E. I.
THERMOELASTOPLASTIC AND VIBRATION CHARACTERISTICS OF COMPOSITES WITH INTERPHASES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-8]
-
Morsy, M. E.
IGNITION DELAY OF JOJOBA BIO-DIESEL AND ITS BLENDS WITH GAS OIL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Mostafa, M. M.
CRACK DETECTION IN BEAMS USING AXIAL AND TRANSVERSE NATURAL FREQUENCIES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
N
-
Naga, S. M.
PREPARATION AND CHARACTERIZATION OF YTTRIA–CERIA DOPED TETRAGONAL ZIRCONIA / ALUMINA COMPOSITES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Nam, K. T.
CONCEPT, THEORY, DESIGN AND EXPERIMENTAL TESTS OF SELFPOWERED LUBRICATION IN CERAMIC COMPOSITE AND ROTORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Negm, H. M.
CRACK DETECTION IN BEAMS USING AXIAL AND TRANSVERSE NATURAL FREQUENCIES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Negm, H. M.
AEROELASTIC OPTIMIZATION OF FUNCTIONALLY GRADED WINGS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-19]
-
Negm, H. M.
MODELING AND ANALYSIS OF SHAPE MEMORY ALLOY LAMINATED COMPOSITE PLATES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-30]
-
Nofel, A. A.
NEW HORIZONS FOR THE EGYPTIAN METALCASTING INDUSTRY: A VISION BASED ON TECHNOLOGIES DEVELOPED AT CMRDI [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-2]
P
-
Pascal, M. A.
EXPERIMENTAL STUDY OF LEAKAGE COMPENSATION ON DYNAMIC CHARACTERISTICS OF HYDRAULIC POWER SYSTEMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
R
-
Rabeih, E. M.
THERMOELASTOPLASTIC AND VIBRATION CHARACTERISTICS OF COMPOSITES WITH INTERPHASES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-8]
-
Radwan, M. S.
A COMPUTATIONAL STUDY OF IN-CYLINDER FLOW CHARACTERISTICS IN TWO STROKE SIE WITH DOUBLE INTAKE MANIFOLDS AT DIFFERENT INCLINATION ANGLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Radwan, M. S.
IGNITION DELAY OF JOJOBA BIO-DIESEL AND ITS BLENDS WITH GAS OIL [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Radwan, M. M.
MULTI OBJECTIVE OPTIMIZATION OF PRESSURE CYCLE OF ABS INJECTION MOLDING PROCESS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Raef, T.
ENHANCEMENT OF PROPULSION PERFORMANCE THROUGH JET NOISE REDUCTION TECHNOLOGIES: A REVIEW [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Ragheb, H.
CONTROL STRATEGY DEVELOPMENT FOR INDEPENDENT WHEEL TORQUE DISTRIBUTION FOR MULTI-WHEELED COMBAT VEHICLE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Ramadan, A. A.
ARTIFICIAL INTELLIGENCE CO-OPERATION WITH CONVENTIONAL METHODOLOGIES FOR CONTROLLING OVER WEAR [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Rashad, Ahmed
INVESTIGATING THE EFFECT OF OXYHYDROGEN ON THE PERFORMANCE OF A COMPRESSION IGNITION ENGINE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Riad, A. M.
EVALUATION OF SHAPED CHARGE PERFORMANCE UNDER ITS VARIABLE FACTORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Riad, A. M.
MODELING STRESS OF SMART BEAM WITH THERMO-PIEZOELECTRIC EFFECTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-24]
-
Roy, A. K.
EXPERIMENTAL STUDIES ON HYDRODYNAMIC CHARACTERISTICS OF A VERTICAL PLUNGING LIQUID JET SYSTEM [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
S
-
Salah, A. B.
MICROSTRUCTURAL MODELING OF INTRINSIC STRESSES IN MULTI-JUNCTION BASED PHOTOVOLTAIC [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-7]
-
Salah, S. A.
INVESTIGATION OF CRITICAL LEAN CULTURE CRITERIA FRAMEWORK FOR LEAN TRANSFORMATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Salah, S. A.
DEVELOPMENT OF LEAN CULTURE ASSESSMENT FOR LEAN MANUFACTURING IMPLEMENTATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Saleh, D. M.
WIND ENERGY MODELING OVER WEST AFRICA [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Saleh, M. A.
PREPARATION AND CHARACTERIZATION OF YTTRIA–CERIA DOPED TETRAGONAL ZIRCONIA / ALUMINA COMPOSITES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Sallam, M. Tolba
EFFECT OF ALLOY COMPOSITION ON THE MECHANICAL PROPERTIES AND FRACTURE BEHAVIOR OF TUNGSTEN HEAVY ALLOYS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Sarhan, S. E.
FEATURE RECOGNITION TECHNIQUE FOR MILLING OPERATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-20]
-
Sarhan, S. E.
COMPUTER AIDED PROCESS PLANNING FOR PRISMATIC PARTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Sedaghati, R.
ANALYTICAL INVESTIGATIONS OF THE GRAVITY EFFECT ON THE DYNAMICS AND PERFORMANCE OF CENTRIFUGAL PENDULUM VIBRATION ABSORBER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Seleem, S. N.
USING COMPUTER SIMULATION IN LEAN MANUFACTURING IMPLEMENTATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-25]
-
Sergaziyev, M. Zh.
DISTRIBUTION OF SUBHARMONIC AND ULTRAHARMONIC WAVES WITH THE NONLINEAR MECHANISM OF DISSIPATION OF ENERGY [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Shabana, Y. M.
THERMOELASTOPLASTIC AND VIBRATION CHARACTERISTICS OF COMPOSITES WITH INTERPHASES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-8]
-
Shalan, K.
A MICROMECHANICS-BASED DAMAGE DIAGNOSTIC MODEL FOR MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-13]
-
Shanwen, T.
NUMERICAL STUDY FOR SHAPE OSCILLATION OF FREE VISCOELASTIC DROP USING THE ARBITRARY LAGRANGIAN EULERIAN METHOD [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-21]
-
Sharaf, A. M.
USE OF GT-SUITE TO STUDY PERFORMANCE DIFFERENCES BETWEEN INTERNAL COMBUSTION ENGINE (ICE) AND HYBRID ELECTRIC VEHICLE (HEV) POWERTRAINS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Sharaf, A. M.
MODELING AND SIMULATION OF HYBRID ELECTRIC VEHICLES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Shash, Y. M.
NICKEL BASE SUPERALLOYS USED FOR AERO ENGINE TURBINE BLADES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-22]
-
Shehata, M. S.
CORN AND SOYBEAN BIODIESEL BLENDS AS ALTERNATIVE FUELS FOR DIESEL ENGINES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Sobhi, N.
INVESTIGATION OF CRITICAL LEAN CULTURE CRITERIA FRAMEWORK FOR LEAN TRANSFORMATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Sobhi, N.
DEVELOPMENT OF LEAN CULTURE ASSESSMENT FOR LEAN MANUFACTURING IMPLEMENTATION [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-16]
-
Sonbol, H. A.
AN INVESTIGATION INTO THE EFFECT OF CNC-EDM WIRE CUTTING PARAMETERS FOR CROSS-FEED TURNING PROCESS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
T
-
Taher, R.
EXPERIMENTAL STUDY OF LEAKAGE COMPENSATION ON DYNAMIC CHARACTERISTICS OF HYDRAULIC POWER SYSTEMS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Tameem, M. A.
PREPARATION AND CHARACTERIZATION OF YTTRIA–CERIA DOPED TETRAGONAL ZIRCONIA / ALUMINA COMPOSITES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
-
Tawfik, M.
CRACK DETECTION IN BEAMS USING AXIAL AND TRANSVERSE NATURAL FREQUENCIES [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-18]
-
Tyurekhojaev, A. N.
MOTION OF AN AXISYMMETRIC RIGID BODY WITH VARIABLE INERTIA MOMENTS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-8]
-
Tyurekhojayev, A. N.
TRANSVERSE OSCILLATION OF THE RAIL WHICH LIES ON THE DISCRETE BASE [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-8]
-
Tyurekhojayev, A. N.
DISTRIBUTION OF SUBHARMONIC AND ULTRAHARMONIC WAVES WITH THE NONLINEAR MECHANISM OF DISSIPATION OF ENERGY [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
X
-
Xu, J.
CONCEPT, THEORY, DESIGN AND EXPERIMENTAL TESTS OF SELFPOWERED LUBRICATION IN CERAMIC COMPOSITE AND ROTORS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
Y
-
Yilmaz, H.
EXPERIMENTALLY INVESTIGATING THE BALLISTIC PROPERTIES OF THE POLYMER-MATRIXED LAYERED AND FIBERREINFORCED COMPOSITE MATERIALS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
-
Ying, L. Q.
A NEW CONCEPT FOR THE LINE OF SIGHT STABILIZATION “BALL STABILIZATION” [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-15]
-
Youssef, A. M.
MULTI OBJECTIVE OPTIMIZATION OF PRESSURE CYCLE OF ABS INJECTION MOLDING PROCESS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-12]
Z
-
Zaid, A. E.
NUMERICAL STUDY ON THE EFFECT OF SECONDARY AIR INLET CONDITIONS ON A GAS TURBINE COMBUSTOR BURNING NATURAL GAS [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-17]
-
Zoalfakar, S. H.
ELECTRICAL CONDUCTIVITY AND DIELECTRIC CONSTANT OF HOT PRESSED MWCNTs/ CARBON NANO FIBRIL COMPOSITE PAPER [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-11]
-
Zoalfakar, S. H.
HOT-PRESSED ELECTROSPUN MWCNTs/CARBON NANO FIBRIL COMPOSITES: POTENTIAL APPLICATIONS FOR BREAKING PADS AND JOURNAL BEARING [Volume 16, 16th International Conference on Applied Mechanics and Mechanical Engineering., 2014, Pages 1-14]
Your query does not match with any item